AUTOMATIC FRAASS BREAKING POINT TESTER
This instrument is used to determine the temperature which a bitumen tends to break rather to flow when cooled and stressed . It can do three tests at the same time in the same environment and calculate the average value.The cooling rate is controlled by computer. It is controlled by micro computer. The cooling rate is controlled automatically. It has automatically timing to bend samples.The test data is shown on the colored LCD and output on built-in printer. Supplied complete with Automatic Breaking Point Tester, Low temp.cyclic Thermostatic bath, Stainless steel sample piece(6 Nos.) and necessary rubber tubings. Other necessary Instruments Viz. Hot Plate, Furnace, Weighing Balance and solvents etc.
AGGREGATE IMPACT TESTING MACHINE WITH BLOW COUNTER (BS - 812)-
Complies with following International Standards : NF P18-574, BS 812. Purpose - For determining the aggregate impact value of coarse aggregate. This test method provides a relative measure of the resistance of an aggregate to sudden shock or impact.
VACUUM DEGASSING OVEN
The Vacuum Degassing Oven (VDO) from ATS has been designed to degas pressure aged binder samples to precisely and accurately meet AASHTO R28-06 and ASTM D6521-05 standards.
VACUUM DEGASSING OVEN - WITH VACUUM PUMP & PLC, HMI CONTROL SYSTEM - ASTM D6521
The Vacuum Degassing Oven (VDO) from EIE has been designed to degas pressure aged binder samples to precisely and accurately meet AASHTO R28-06 and ASTM D6521-05 standards.
CO2 CURING CHAMBER FOR 10 SAMPLE OF 300 X 300 X 20 MM
Steam curing of concrete blocks is an energy extensive process and contributes to a significant portion of the block production cost. CO2 curing of concrete blocks consumes CO2, reduces energy consumption and produces dimensionally more stable products. This study investigated the strength development and weathering properties of steam- and CO2-cured full size lightweight concrete blocks.
PAVEMENT INTENSITY TEST APPARATUS
Digital type with load cells LVDT with digital indicator.
UNIVERSAL LOAD FRAME - DIGITAL - 50 KN-
The Universal load frame is a system designed for carrying out 3 different tests, mainly CBR Test, Unconfined Compression test and Marshal Stability test. The Load Frame is equipped with a Digital Speed indicator on which any pre-defined speed can be digitally set. There no gear and lever to mechanically adjust the loading speed. The Load can be measured either by a Proving ring or Digital Load Indicator . Similarly, the displacement can be measured by Dial Gauge or LVDT.Digital Universal Load indicator with LVDT and software are offered separately. Client can also use his own proving ring and dial gauge if he so desires. Cost of Load Frame only.
UNIVERSAL LOAD INDICATOR - MARSHAL - CBR - UCS
TOUCH SCREEN UNIVERSAL LOAD INDICATOR - CONTROLLER - can be used to conduct the marshal, CBR and UCS test. The indicator will come complete with load cell - 50 kN and LVDT - 25 mm.
BENDING STRENGTH TEST APARATUS - FOR CABLE DUCT AND COVERS
The bending strength of concrete culvert. Electro-hydraulic Design, quite and vibration free operation. PC connectivity with software available at extra cost.
FULLY AUTOMATIC DIGITAL MORTAR MIXER - EN 196-1, EN 196-3 - 4.75 LTR
The Fully Automatic Digital Mortar Mixer is designed for the preparation of standard cement mortar prisms in accordance with EN 196-1, EN 196-3, IS 4031, and ASTM C451. It features a 5-liter nominal capacity, microprocessor-based control, and an integrated sand dispenser for accurate and repeatable mixing.
CREEP TESTING MACHINE FOR CONCRETE- 1000KN - ASTM C512
The machine is designed to determine the creep of the concrete cylindrical mold subject to sustain longitudinal compressive load as per ASTM C 512. The test method is limit to concrete in which the max aggregate size does not exceed 50 mm. The machine will be supplied with DAQ for the stain gauge and 10 pieces of stain gauge of Type -BF120-60mm,Resistance- 120ohm ,lead wire -25-30mm. It will also supplied with EPOXY ADHESIVE to paste of the sample and cable to solder the stain gauges.
FLAKINESS GAUGE - COMPLETE S.S.
Used to determine the percentage of particles in a coarse aggregate material that have a thickness (smallest dimension) of less than one-half of the nominal size. Particle is flaky when its thickness (smallest dimension) is less than 0.6 of the mid-size of the sieve fraction.
PAN MIXER-60 LTRS-WITH REMOVABLE PAN, TROLLEY AND STAND
Suitable to Cast at least 12 Cube Mould of 15 cm at a Time in single batch. The machine is capable to caste second batch immediately after first batch as the first pan can be removed with trolley and placed on the table. And with the help of second pan, second mix design can be started.
40 MM SQUARE PLATTEN SET- FOR COMPRESSION FRAME JIG ASSEMBLY - EN 196
This jig is designed for testing of 40 x 40 x 160mm cement prism after breaking in Flexure and also can be adapted with 50mm platen to test 2” or 50mm mortar cement cube specimen. This jig can be fitted to Compression Test Machine
ACRYLIC - SLUMP TEST APPARATUS - MINI
Kantro Mini-Slump Cone, The Kantro layout is widely accepted in research and laboratories to test the fluid flow and rheology of cement paste or mortar. Made of Acrylic, Dimensions of mini-slump apparatus 38 mm high with at the top diameters of 57 mm and 19 mm at the bottom. Base plate (Glass/acrylic) available at extra cost
PERMEABILITY APPARATUS FOR GEOTEXTILE - AUTOMATIC - ASTM D4491 - FALLING HEAD TEST - NO LOAD CONDITION
Closed loop system comprises of Main working unit mounted on Table Top Bench with back support, Upper unit made of Transparent acrylic material, Geo‑textile specimen holder assembly between Upper & Lower unit, Inlet and outlet valves with PVC Pipe network, Head change measurement using Automatic Solenoid valve, Continuous Liquid Level Sensor & Dedicated HMI Touch screen controller. Complete with Overhead and Bottom Collection tank.
PERMEABILITY APPRATUS FOR GEOTEXTILE-MANUAL OBSERVATION--CONSTANT HEAD TEST-NO LOAD CONDITION-WITHOUT TANKS AND CIRCULATION SYSTEM
Comprises of Main working unit mounted on Table Top Bench with back support, Upper & Lower unit made of Transparent acrylic material, Geo‑textile specimen holder assembly between Upper & Lower unit, Inlet and outlet valves with PVC Pipe network, Head differential measurement arrangement mounted on a stand, Manual observation of quantity of flow (in case of Constant Head Test).
