SURFACE ABRASION TESTER FOR CONCRETE & MORTAR BY ROTATING CUTTER METHOD - ASTM C944
Abrasion Resistance of Concrete can be used as a measure of its durability. Concrete surfaces may deteriorate in the long run due to abrasion caused by various factors such as sliding, scraping and abrasive materials carried by water etc. Supplied complete with Rotating Device, Agitation Paddle,Test Container and Abrasive Charges. Mould to prepare the sample available at extra cost
SHEAR STRENGTH TESTING MACHINE FOR MASONRY - ASTM E519
The Shear Strength Testing Machine for Masonry is a computer-controlled servo-hydraulic testing system designed for evaluating the diagonal tensile (shear) strength of masonry panels in accordance with ASTM E519. The machine provides accurate load application, and automated data acquisition through an integrated touchscreen control system, ensuring reliable and repeatable test results.
SIEVE SHAKER - FOR RECTANGULAR SIEVES - 45.7 X 66 X 7.5 CM
The body and the base of Sieve Shaking Machine is made of mild steel and the top rotating plate is made of mild steel / plate with arrangement for fixing 10 Nos. test sieves 45.7 cm (L) x 66 cm (W) x 7.5 cm (H) with rigid clamp. Supplied Without Sieves.
SAND CONE TEST APPARATUS-(ASTM D1556)
The Sand Cone Apparatus is used to determine the in-place density and unit weight of any soil that can be excavated to a stable condition with hand tools.
VIBRATING MACHINE WITH DIGITAL TIMER-
The machine shall be capable for compaction of cement mortar cubes as per IS: 4031 and designed as per Standard IS : 10080. The complete frame assembly consists of device to hold a 7.06 cm cube mould to feed the sample in the mould. The frequency of vibration is 12000 ± 400 R.P.M. Vibration per minute. Supplied complete with one 7.06 cm cube mould with DIGITAL Timer. Complete with One No. poking rod to meet IS: 10086 requirements. The electric motor will be of reputed make such as GODREJ/CROMPTON MOTOR.
RELATIVE DENSITY APPARATUS-(ASTM D4253)
Relative density (also called density index) measures the compactness of cohesionless soils (sands, gravels). It indicates how close the soil is to its loosest or densest state, useful in foundation design, compaction control, and evaluation of liquefaction potential.
ELASTIC RECOVERY MOULD - SET OF 3 NOS.
With base Plate for casting mould
CBR/UNCONFINED LOAD FRAME-3 SPEED-DIGITAL-
Load Frames are useful device employed for application of compression and penetration loads required for various tests such as unconfined compression test, Triaxial Shear test, California Bearing ratio test etc.
IN-PLANE WATER DISCHARGE CAPACITY TEST OF PREFABRICATED VERTICAL DRAINS - PVD - ISO 18325
In-plane Water Discharge Capacity Test is used to determine the in-plane water discharge capacity of prefabricated vertical drains (PVD) under a specified pressure.
BENTONITE SLURRY SAMPLER - 50 MTR. WITH ROPE
Slurry-Sampler is designed for capturing samples of drilling fluid from any specific depth within an excavation or borehole. This special sampler assures slurry samples taken produce a representative sample for proper test results. The use of a sampler is important for exact depth confirmation of viscosity, specific gravity, pH, and sand content data collection in the drilling fluid.
JAR ROLLER MILL-SEDIMENTATION METHOD-IS 2386
A device for rotating the jar about its long axis, with this axis horizontal, at a speed of 80±20 rev/min. With Digital RPM Meter and controller.
DIRECT SHEAR APPARATUS-MOTORIZED-SINGLE SPEED-ELECTRONIC DIGITAL-
Electronic Direct Shear Testing Machine As per IS : 2720 (PART 13) 1986 / IS : 11229 - 1985.
DIGITAL TRIAXIAL SHEAR TEST APPARATUS- FOR 38 MM DIA SPECIMEN - FOR UU TEST
The Triaxial Test System provides triaxial compression tests on cylindrical undisturbed and remolded soil samples. Unconsolidated undrained (UU), can be carried out using this apparatus. Supplied complete with Triaxial cell for 38mm dia specimen, Multi speed Loading Frame 50 KN with Load Cell and lateral pressure assembly. To work on 220/230 Volts, single phase, AC power supply. Extra to cost : Pore Pressure Transducer, LVDT, Air/Water Constant Pressure system with air compressor. De-airing system with vacuum pump, Automatic Volume change gauge, Three Cell Saturation Device, wall mounted. Split Molds, Three Part split Molds, Sample extractor etc. can be quoted on request. Further details as per the following pages.
SCRAPPER - FOR JOLTING APPARATUS
The scraper made of semi-rigid rubber blade, attached to a handle about 150 mm long. The blade will be about 75 mm long, 50 mm wide and tapered to a thin edge about 2 mm thick.
DUCTILITY TESTING MACHINE - THERMOSTATIC - (NON-REFRIGERATED) - (IS 1208)-
As per IS : 1208. Non Digital, with Thermostatic control. Complete with 3 Nos. Ductility Moulds. Digital temp. controlled machine available at extra cost, if desired. Mould casting plate (3 Nos.) to be procured at an extra cost. Further details as mentioned in detailed description.
MORTAR MIXER-4.75 LITERS-IS 10890
As per IS:10890.00. The instrument is specially designed to prepare paste of cement mortar for Strength Determination. It is used for mixing cement pastes, mortars and pozzolanas. It can also be used for uniform mixing of soils with additives such as lime, cement, etc.
