UNCONFINED COMPRESSION TESTER-(MOTORISED)-(IS 2720-PART X)
The Unconfined Compression Test is widely used to determine the unconfined compressive strength (UCS) of cohesive soils, which provides insight into the soil’s ability to withstand load without lateral support. The primary goal of this test is to determine the unconfined compressive strength of soil, which is a measure of its resistance to axial loading without any confining pressure. It is particularly applicable for cohesive soils (e.g., clay) that are fully saturated. As per IS : 2720 (PART‑X), IS : 4332 (PART‑V)
Theoretical Density Meter With Vacuum Pump - ASTM D2041-03
Used for determining the theoretical maximum specific gravity of uncompacted bituminous paving mixtures. The set consist of two vacuum containers, vacuum pump with digital vacuum indicator, vibratory table and control panel. ( Commonly referred as "Rice test")
PAN MIXER-40 LTRS-WITH REMOVABLE PAN, TROLLEY AND STAND
Suitable to Cast 9 Cube Mould of 15 cm at a Time in single batch. Detailed specifications mentioned in the long description. The machine is capable to caste second batch immediately after first batch as the first pan can be removed with trolley and placed on the table. And with the help of second pan, second mix design can be started.
SAND EQUIVALENT MECHANICAL SHAKER - MOTORIZED (ASTM 2419)
The sand equivalent test provides insight into the cleanliness and quality of fine aggregates. The sample is typically prepared by removing larger particles and then mixing with a solution to create a suspension. The suspension is shaken to distribute the fine particles uniformly throughout the solution. A mechanical shaker is recommended for consistent, repeatable and time-efficient results. With Digital RPM indicator and Digital timer. As per ASTM D‑2419, AASHTO T‑176, T‑210, IS:2720(P-37)
SLIDE WARMING TABLE-S.S. TOP-S.S. BODY-30 X 22 X 15 CM-
Slide Warming table is good for cytology, histology, pathology, biology and clinical laboratories which are engaged in paraffin tissue embedding and section mounting. It provides uniform heat transfer over the entire surface. The work surface is made up of Stainless Steel and it is good for specimen contrast.
WATER RETENTION TEST APPARATUS - (ASTM C1506, ASTM C110)
The apparatus is used in specification tests of masonry cement and physical testing of quicklime and hydrated lime. As per ASTM C110, ASTM C91, ASTM C1506, ASTM C207
CONSTANT PRESSURE SYSTEM - AIR/WATER
The air/water constant pressure system in a triaxial test system is used to apply and maintain a stable confining pressure around the soil sample, which is crucial for conducting triaxial tests. Used in applying Confining Pressure and maintaining Pressure Stability. A consistent confining pressure is essential for accurate measurement of stress-strain relationships and other soil properties. By keeping the confining pressure constant, the system aids in analyzing the effective stress when combined with pore pressure data (from a pore pressure measurement device). This combination provides insight into the strength and deformation characteristics of the soil sample under controlled stress conditions.
LENGTH COMPARATOR -IS 9459, IS 4031, ASTM C490
Compliance Standards: IS 4031, IS 9459, ASTM C452, ASTM C151, ASTM C490, The apparatus consist of an adjustable length comparator with Digital dial micrometer of 0.001 X 10 mm, together with a suitable reference bar.
DYNAMIC CONE PENETRATION TEST APPARATUS (DCPT) ASTM D6951
The Dynamic Cone Penetrometer (DCP) test is used to assess the structural properties of soil, granular materials, and pavement layers by measuring the rate of penetration of a cone under repeated impacts. As per ASTM D6951, IRC:SP:72
HYDRAULIC JACK - 500 KN WITH PRESSURE GAUGE AND HAND PUMP
For applying loads for various tests in field or laboratory. Hydraulic jack with separate pumping unit. Complete with 5 meter long Flexible rubber hose pipe and 18 ltr Hydraulic Oil. Jack with Loading Capacity upto 2000 KN available.
